Visit

 

 

How do you actually feel with regards to How to Install a Bathtub Yourself?

Mounting a tub isn't specifically rocket science, however it does require solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately tough project. If the old tub is conveniently accessible, the project can relocate speedily; if you have to open up a wall surface to remove the old bathtub and also position the new tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and also set in the new one. Make certain you have certified on your own for the job as well as fit trying it. Rather than employing a specialist to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This write-up will help you set up a new tub in your washroom if you have actually already acquired a brand-new bathtub and don't need to change the plan of your previous water system pipelines.
Your devices and also product list need to comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Getting ready for the Installation

Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its final position.

 

 

Removing Old Touches

If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather problematic as a result of the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will originate from the pipelines. When the supply pipelines have been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.

 

 

Mounting the Bathtub

Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are handy in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the bathtub up until the level reads level.
To set up faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Activate the supply of water as well as examine all joints and new pipework for leaks as well as tighten them if essential. Load the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has actually been made use of at the very least when as this will settle it into its final position.

 

 

Fitting New Taps

If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the producer provided backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The previous type ought to be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Tub

In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, creating the water to permeate the wall in between the bath and also the tiling, causing complications with wetness as well as feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are sold in tubes as well as cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before sealing, to enable the activity experienced when the tub remains in use. The sealer can fracture relatively early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you really like reading up on Installing A Bathtub? Make feedback below. We'd be delighted to know your suggestions about this blog. Hoping that you visit us again in the near future. Feel free to take the time to distribute this blog if you liked it. We truly appreciate reading our article about How to Install a Bathtub.

Book My Estimate